Configure Automatic Rework Data Collection
Learn how to configure a Rework Signal in GS Desktop to automatically register products requiring rework and optionally assign a Rework Reason.
Overview
Good Solutions can automatically collect information about products that require rework.
A Rework Signal registers a pulse when a machine or connected sensor identifies a product requiring additional processing.
Unlike scrap, rework represents products that require corrective processing rather than products that are discarded.
Automatic rework registration can help production teams:
- Monitor rework quantities.
- Identify recurring quality problems.
- Reduce manual registration.
- Understand the impact of rework on production.
- Improve the completeness of quality data.
How Does a Rework Signal Work?
A Rework Signal can be generated by an internal or external machine sensor.
For example, an inspection station might generate a pulse whenever a product is directed to a rework area.
Good Solutions receives the signal and registers the corresponding rework quantity.
A Rework Factor determines how many units each pulse represents.
| Rework pulses | Rework Factor | Registered rework |
|---|---|---|
| 5 | 1 | 5 units |
| 5 | 2 | 10 units |
| 5 | 4 | 20 units |
Before You Begin
Make sure that:
- The machine provides a suitable Rework Signal.
- The signal is available through an I/O interface.
- The appropriate Measure Point exists.
- Any Rework Reason you want to assign has been configured.
- You know how many units each signal represents.
Step 1: Create a Rework Signal Connection
- Open GS Desktop.
- Navigate to Settings → Machine Data.
- Select Rework Signal Connections.
- Click Create.
A new connection is created.
Step 2: Configure the Rework Factor
Enter the Rework Factor for the signal.
The factor determines how many reworked units are registered for each incoming pulse.
For example, if one pulse represents two products requiring rework, set the Rework Factor to 2.
Step 3: Assign a Rework Reason (Optional)
You can configure an automatic Rework Reason.
- Click the Rework Reason connection icon.
- Select the appropriate reason.
- Click Save and Close.
For example, a machine signal might identify products requiring rework because of an incomplete assembly operation.
If the signal does not distinguish between different reasons, consider whether assigning a specific reason would be appropriate.
Step 4: Select the Machine Input
- Click the I/O-Interface Input connection icon.
- Select the correct I/O interface.
- Select the input carrying the Rework Signal.
- Click Save and Close.
Make sure the input is connected to the intended machine signal.
Step 5: Connect the Signal to a Measure Point
- Click the Measure Point connection icon.
- Select the Measure Point that should receive the rework registrations.
- Click Save and Close.
Step 6: Save the Configuration
Review the connection and confirm that:
- The Rework Factor is correct.
- The Rework Reason is correct, if configured.
- The intended I/O input is selected.
- The correct Measure Point is assigned.
Click Save and Close to finish.
Verify Your Configuration
Test the signal using a known number of rework events.
Example:
An inspection station identifies eight products requiring rework.
The machine generates eight pulses, and the Rework Factor is 1.
Good Solutions should register eight reworked units.
Verify that:
- The correct quantity is registered.
- The intended Measure Point receives the data.
- The Rework Reason is correct, if configured.
- The results are reflected in the relevant quality information.
Common Problems
No rework is registered
Check that the signal is reaching the selected I/O input and that the connection is saved.
Incorrect rework quantities
Verify the Rework Factor and the number of pulses generated.
Incorrect Rework Reason
Review the assigned reason and confirm that it matches the machine signal.
Rework appears under the wrong Measure Point
Check the Measure Point connection.
Key Takeaways
- Rework Signals allow automatic registration of products requiring additional processing.
- The Rework Factor determines the quantity represented by each pulse.
- Rework Reasons can be assigned automatically.
- Every signal must be connected to the correct I/O input and Measure Point.
- Always test the configuration against actual production events.